Kreg SML-C250B-250 Blue-Kote Weather Resistant Pocket Hole Screws - 2 1/2", #8 Coarse, Washer Head, 250 count

Buy Cheap Kreg SML-C250B-250 Blue-Kote Weather Resistant Pocket Hole Screws - 2 1/2", #8 Coarse, Washer Head, 250 count

Buy Low Price From Here Now
Three chemically-combined anti-corrosion layers give Kreg's Blue-Kote screws up to 400% more weather resistance than zinc-plated screws. They're an ideal choice for garden and patio furniture, as well as for general exterior construction. Self-tapping screw tips make for easy driving. Case hardened steel won't bend or break, and the deep-seated #2 square drive heads eliminate "cam out," ensuring a tight, solid joint.



Readmore

Technical Details

- Great for outdoor applications
- Performs 400% better in corrosion resistance than our old zinc-plated screws
- Large Maxi-Loc Head stops when it hits the bottom of the hole
- Needle sharp point minimizes walking
- Sharp edge of self-tapping tip drills a cleaner pilot hole
See more technical details

 "Kreg Screws - Great Product" 2008-11-19
By George S (California)
I use these screws for general wood working as well as with my Kreg jig. They really work well since their flat head does not tend to split the wood like dry wall screws do. Also the course thread gives good "bite" in softer wood.

 "Thanks again Kreg!" 2008-08-21
By The Engineer
These washer head screws are fantastic. They clamp the parts tightly without splitting the wood. They run in fast and easy. Wherever you have a pocket hole application, or wherever you don't mind a visible screw head (not countersunk, although they could be counterbored), use a washer head screw for maximum clamping. Oh, and I haven't broken any off yet, like many other screws.


Images Product

Buy Kreg SML-C250B-250 Blue-Kote Weather Resistant Pocket Hole Screws - 2 1/2", #8 Coarse, Washer Head, 250 count Now

Kreg KMS7714 48-Inch Top Trak

Buy Cheap Kreg KMS7714 48-Inch Top Trak

Buy Low Price From Here Now

Readmore

Technical Details

- Mounts to 3/4-inch fence
- Accepts head of standard 1/4-inch bolt
- Self aligning L-shaped mounting foot for easy installation
- Recess for 1/2-inch measuring tape
- 4-foot length
See more technical details

 "Kreg Top Track - Fantastic" 2009-01-29
By C. Hubler
I bought these to complete a miter saw fence and they are perfect. Installation is easy, they work on 3/4" stock with no problem, the measuring tape fits nicely and the stops made for the tracks slide easily. This is a nice solid machined addition to any fence you need to make for the shop. Now I need to pony up and buy them for the rest of my tools that need them!

 "Very happy!" 2008-06-14
By S. Griffin (Victor, Idaho)
I'm very happy with my Kreg track and stop system. Setting up your miter saw with stop system is mandatory in my opinion. The old tape measure/pencil mark/chase the mark and make a cut method is such a waste of time I'm amazed when I see builders doing it. Need 8 cripples at 33"? Set the stop and chop as fast as you can. And they come out perfect. Not having a stop system for your miter saw is a dumb as not having a measuring scale on your table saw.



I've used the Beismeyer stop for 10 years and they work well. But they are so proud of their little stop they think it's worth over $100. For that price opted to buy 2, 4' kreg tracks and the flip stop. It works every bit as well was easier to set up.



The track is easy to mount, is ridged and dead straight. There is even a little groove to lay the adhesive measuring tape into.



The hairline gauge allows very precise settings. (Beware that many of the cheap $39 dollar stops you can buy have a magnifying bubble over the hair line--sounds great, but when you look at it from different angles it moves back and forth a 1/16 of an inch! That's the sort of stuff that gives engineering a bad name...)



So my advice--DO NOT buy a miter saw without also building a table, fence and Kreg stop system. Sure it will take a couple hours cost $100, but it will be worth it.



-Steve

 "Great time saver!" 2008-02-20
By William R. Bonner III
Once completing the easy setup, the Top Trak is a great time saver. I installed mine to the left of a Sears Radial Arm Saw. I've used it for cutting the rails and stiles on several raised panel doors along with cutting the drawer sides. Very accurate and repeatable. Make sure to add the Kreg tape (left or right for your application) along with either the Flip Stop or Production Stop. I bought both. The Flip Stop is more convenient if you are using the saw for cutting boards to various lengths because it can be moved out of the way quickly if necessary.


Images Product

Buy Kreg KMS7714 48-Inch Top Trak Now

Kreg KJD Replacement Twist Step Drill Bit for Kreg Manual-Pocket Hole Systems

Buy Cheap Kreg KJD Replacement Twist Step Drill Bit for Kreg Manual-Pocket Hole Systems

Buy Low Price From Here Now
The 1 piece design eliminates clogging and provides a much smoother and faster drilling stroke than the drill bits with replaceable center drills. The KJD bit for our manual pocket hole jigs is made of high speed steel that increases the bit's life.
Readmore

Technical Details

- Drill bit for use with pocket hole joinery
- Small tip includes clearance hole for screw shank
- Large diameter creates flat-bottomed hole
- Recommended for use with corded high-rpm drills
See more technical details

 "High speed steel, high polish, very sharp" 2008-12-06
By New England Yankee (Northern New England)
These are tailor-made for drilling pocket holes - not just because of the stepped design, but because of their high-polish, sharpness, and temper. Drilling a lot of pocket holes in a row generates a lot of heat, and these bits hold up to the heat and keep their edge.



If you are replacing a lost bit, be aware that this bit does not include the depth collar, which may be found here: Kreg H9474 Depth Collar w/ Allen® Wrench



Kreg also makes a square shank version, for quick-change bit holders: Kreg Hex Shank Pocket-Hole Drill Bit and a quick change set including the quick-change driving bit: Kreg Quick-Change Pocket-Hole Kit.



Finally, Kreg also makes cobalt steel bits that can be used either in their pocket hole machines or in a hand-held drill. These are exceptionally hard and will hold up to extreme use and high heat. They are expensive, though, and if you are going to use one in a hand-held drill, make sure you buy the right-hand twist version: Kreg DKDB 3/8-Inch Step Twist Drill Bit for Pocket Hole Machines.

 "This Step Drill Bit Gets The Job Done" 2007-11-21
By Robert 93940 (California)
These step bits work very well in the pocket hole jig. However, the small diameter tip can break off if one is not careful, so I keep a spare bit on hand.

 "great spare" 2007-11-14
By rprice54 (USA)
I have one of the 'generic' pocket hole jigs you can get at most big box home improvement stores. when my original bit broke, I was in the middle of a project on a rare day off, so I had to buy a whole other jig set ($30) in order to keep going. So I decided a spare would be a good idea. This is the best price on a spare bit I could find. The Kreg bit seems to be a little sharper than the generic one that came with my jig, so the generic bit is now my backup.



It's a good idea to keep one extra around. They are good bits, but the tip is definitely the weak point of the entire system. hopefully the kreg bit is a little better made.

 "Kreg pocket hole bit" 2007-01-04
By Robert F. Leroux (Ogdensburg, New York United States)
Tried other manufacturers but recommend using only this Kreg step drill bit. The metal seems to be harder and the pilot hole a better length than other step drill bits.

 "Top Tools" 2006-03-10
By Gary Strothenke (Adirondacks, NY)
Outstanding tool and superior quality. (I needed spare bits - they occasionally dull and on rare occasion, when pushed too hard in very hard wood, the tip may break) I laid my hands on a Kreg Jig about 7 years ago and had to have one. Now it is one of the most used tools in my shop. I build furniture and Cabinets, and have found the quality of my product has increased and the speed of production has trippled. What a Tool, I cannot say enough good about it. Buy one and use it! You will not be sorry.


Images Product

Buy Kreg KJD Replacement Twist Step Drill Bit for Kreg Manual-Pocket Hole Systems Now

Kreg NZ03 Magnetic Drawer Slide Mounting Tool

Buy Cheap Kreg NZ03 Magnetic Drawer Slide Mounting Tool

Buy Low Price From Here Now
The Kreg Magnetic Drawer Slide Mounting Tool simplifies the work of positioning your metallic slides to ensure smooth gliding drawer movement in cabinets. It uses the intersection of the cabinet stile and rail in face frame cabinets, and the cabinet side in frameless cabinets, as a reference point for positioning a slide perfectly parallel to the drawer opening. Simply place a metallic drawer slide into position on the base of the tool, which uses magnets to hold the slide in place, align the tool where the stile and rail meet, and drive the screws for a perfect alignment every time.
Readmore

Technical Details

- Simplifies slide positioning for cabinet drawers
- Tool uses reference points to position slides parallel to drawer openings
- Works with most kinds of metallic slides
- Produces a perfect alignment at each use
- simplifies the process of positioning your slides accurately
See more technical details

 "Need? No. Like? Yes." 2009-07-30
By rwizard (USA)
If it works with your slides, you may not actually "need" this gadget, but you will "like" this gadget. 'nuff said !

 "The Third Hand You Always Need" 2009-07-16
By Rustic Dave (Northern, ME)
Worked well with the bottom mount slides on a 20 drawer face frame built-in. Did need a little tweaking with the rear alignment, but that was because of my design. Magnets are strong and hold well. Did not get the Kreg clamp, almost any small clamp (C-clamp, quick grip, etc.) in your shop should work. Would recommend.

 "Another very handy tool" 2009-07-04
By R. A. Stine (San Mateo, CA)
If you're installing new drawer hardware, this can make it much easier. Perfect alignment every time.

 "works GREAT" 2009-03-29
By Paul J. Baribeau
This tool is easy to understand and use, with common sense it makes drawer guides easy! Jeff Baribeau Carpentry

 "Excellent tool, or is it a jig?" 2008-09-10
By George Gonzalez (Miami, FL)
Seems more like a jig to me, but whatever it is, it works! Consistently excellent results on side mounted slides. I use this with Kreg's drawer mounting brackets and I recommend getting them together. I've used this jig for undermount slides with some good results also. I can find a few more uses for it to hold metal brackets and other pieces square to a wooden or plastic workpiece in order to attach them.


Images Product

Buy Kreg NZ03 Magnetic Drawer Slide Mounting Tool Now

Kreg SK02 Pocket Hole Screw Kit

Buy Cheap Kreg SK02 Pocket Hole Screw Kit

Buy Low Price From Here Now
Includes plenty of screws in five sizes in both fine and course threads.
Readmore

Technical Details

- 1-to-2-1/2-Inch screws for pocket hole joints; 5 popular styles for use in hardwoods or softwoods
- Self-drilling auger point, prevents wood splitting and eliminates need to pre-drill
- Case hardened steel screws for added strength of a pocket hole joint
- Screws have a deep no. 2 Square drive to prevents driver from jumping out; Dri-lube finish reduces driving torque needed
- 675 Screws organized in a illustrated and labeled semi-transparent plastic carrying case
See more technical details

 "Pocket screw joints" 2009-04-06
By Randy Bartholomew
I love the Kreg system and now use it on almost all of my projects. My only regret is I wish I had invested in the system a long time ago!

 "Excellent service from company" 2009-02-07
By KittyKat (East Hartford, CT USA)
We had a small problem with the product, and the company immediately

corrected the problem and we received the best service from an online

purchase ever. Highly recommend dealing with PriceCutter.

 "Good value" 2008-09-24
By J. Tsai (Bellevue, WA)
Decent set of screws for a good value. I use it for more than just pocket holes.

 "Great Product! Strength really makes the difference" 2008-04-27
By Raymond E. James (Morehead, KY)
I purchased this kit soon after I purchased the Kreg model R3 Jig. It's Amazing how fast and strong the joints are when using these screws and also very simple. I will recommend these screws and Jig kit to all my friends.

I had used the phillips type screws for several years and went through many bits, but the square slot screws are Great!

 "Poor service and NO Shipping" 2008-02-22
By Doug Lawton (Lake Burton in NE Georgia)
I ordered this item through Amazon on December 12th, 2007. Today is February 22nd, 2008 and I still haven't received it.



Website says it's IN STOCK, but won't be shipped until March 17th. WTF??



Second tier supplier has not contacted me with an explanation for the delay.



I'll purchase locally from now on.


Images Product

Buy Kreg SK02 Pocket Hole Screw Kit Now